News Company News Industry News Exhibition Schedule Product knowledge

The cabinet door hinge installation method in detail

Hinge, links and cupboard door main hardware fittings, cabinet put oneself in another's position in daily life, we use ambry, hinge has been subjected to the test.Countless times every day of the open and close the cabinet door, let hinge under so much pressure, so the quality of the hinge is good or bad will directly affect the cabinets can be normal use for a long time.But there is still a little is also very important, and that is the installation of the hinge, the hinge is installed, solid, this is very critical, even if it is a good quality hinges, failed to good installation, so also can't play its role and advantage.Is the so-called "three is divided into seven quality installation", let's take a look at the installation of cabinet door hinge.
1, the door from the smallest:

First of all, we want to make sure that you want to install the cabinet door between the from the door, or two doors are always "fight" will not beautiful also not practical.The door from the smallest according to the type of hinge, hinge cup edge distance and the thickness of cupboard door to select values.For example: door plank thickness of 19 mm, hinge cup margin of 4 mm, then the distance of 2 mm near the door.You can refer to the table below.
2, the selection of number of hinge

Ambry links use experiments to determine the quantity according to the actual installation, door plank with depends on the number of hinge door width and height, the weight of door plank, the material of door plank.For example: height is 1500 mm, between 9 and 12 kg weight of door plank, should choose three hinge.

3, ambry shapes that meet the needs of hinge:

With two built-in can rotate play goal of ambry, need fixed door and door frame at the same time, the most important thing is that because of the built-in pull basket will determine the opening Angle of the very large, then the curvature of the hinge must be large enough, can ensure freely to open cupboard door at just the right Angle, easy to take place any items.

4, selection of hinge installation method:

Open the door by the door and the position of the side plate side, have full cover door, half cover door and embedded door three installations.Full cover door basically covered the side plate;Half cover door had covered half of the side plate, is especially suitable for the middle clapboard, the need to install more than three door cabinet;Embedded door is loaded in the plate on both sides.

5, the adjustment of the door plank:

By means of the fixed screw loose hinge seat, sliding hinge arm position, before and after the adjusting range is 2.8 mm.After the adjustment, it is necessary to tighten the screw again.

1) before and after the ordinary hinge seat adjust: through the fixed screw loose hinge seat, sliding hinge arm position, before and after the adjusting range is 2.8 mm.After the adjustment, it is necessary to tighten the screw again.

(2) using cross hinge seat quickly adjust: before and after the cross fast loading type hinge seat has a screw drive the eccentric CAM, turn the CAM can be in 0.5 mm to + 2.8 mm range adjustment, don't need to loosen the other set screw.

(3) using a glyph fast hinge seat adjust: before and after this one glyph fast loading type hinge seat has a screw drive the eccentric CAM, turn the CAM can be in 0.5 mm to + 2.8 mm range adjustment, don't need to loosen the other set screw.

(4) door side to adjust: hinge after the installation, before don't do any adjustment, the door should be 0.7 mm.Such adjustment screw on the hinge arm can be in 0.5 mm to + 4.5 mm within the scope of adjustment.If you use the thick door hinge or narrow door hinge, this parameter range is reduced to 0.15 mm.

The above content is about cabinet door hinge installation method of introduction, hope that through the introduction of the above content, you have certain understanding to any installation hinge, oneself also can install cabinet hinge, hinge and can damage for replacement.

HELEN

86-13798106771

HELEN

KIN

86-15918428719

JCINTA

86-13434101983

MAY

86-13352834225